• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유

How to Fix a Loose Door Hinge

Fixing a loose door hinge can be a doable job for most homeowners. But, if the screw holes are stripped and can't hold screws, you might have to add dowels and wood glue before you can put back the hinge.

Before you do that, however you should clean off any surface corrosion. This will help the dowels remain in place and provide them a solid base to rest on.

Take the Hinges off

Many standard door hinges can be removed, which makes it easier to move the door from one end of the frame to the other side or remove the entire door if necessary. Anyone who is patient can remove the hinges but you need to know what to do.

If the hinges are painted you will need to remove the paint before attempting to remove the pins. You may scratch your door if you don't remove the paint. To break the seal put the hinges in an stainless steel pan and fill the pan with water until the hinges are completely submerged. The hinges should remain in the pan for around 30 minutes. The heat of the water will soften the paint making it easier to take off.

Once the pins are loosened then you can remove the hinges from the door and frame. You can make use of a screwdriver to get the job done, but it is recommended to use a magnetic screwdriver for this project. This type of screwdriver is designed to remove screws made of metal and make the task run much more quickly.

It is a good practice to spray lubricant onto the hinges before attempting to remove them. A simple lubricant will help you move the process along faster and also remove the screws and pins easier. You can find this kind of lubricant in most hardware and home improvement stores.

It is important to keep in mind that the number of door hinges you'll require will vary depending on the type of door and its settings. Doors with solid cores and heavy weights will require more hinges whereas lighter and hollow-cored doors may only require two or three hinges.

Understanding the different types of hinges can help you determine which one is suitable for your situation. Exterior hinges are generally designed to support the door's weight, while interior hinges will need glass to glass hinges be able to handle heavier loads.

Reattaching the Hinges

Over time, a door hinge can loosen and begin to slide or hang crookedly. This can be a problem however, it's usually simple to fix. Most of the time, a simple retightening of the screw will fix the issue. However in the event that the screw holes are ripped out, it can be more difficult. Fortunately, there is a trick to get these holes back to their original size that uses a wood dowel.

Start by drilling the hole using a drill close to the size of the new screw (normally 3/8"). Then, you can use a wood glue and a dowel made of wood to fill the hole. To ensure a tight fit, the dowel should be cut to the same length as the screw. Then, reinstall the screw and tighten it to the desired level of tightness. If the door continues to bind up, you can insert another dowel into the gap. Repeat the procedure. Close the door slowly after each adjustment to ensure that the perimeter clearances are in order.

You can also use a wooden plug in place of the dowel. It works just as well but might take a little longer to put in. Simply whittle a piece of wood that is the right size for a snug fit, then tap it into the hole. If you don't have a wooden tool You can also make use of toothpicks or wooden matches.

After you have reinstalled the new screw and countersink the screw, you can use a countersink tool to make the hole for the head of the screw smaller, so that it doesn't be able to rub against the edge of the door when it's open and closed. This will make it much easier to tighten the screws before reinstalling hinges.

After reinstalling the hinge, apply lubrication to the hinge using an oil-based lubricant that is dry. This will help prevent it from getting stuck in the future. You can use products such as PB Blaster and Liquid Wrench. You should apply a light coat and allow it to take approximately 15 minutes to reach the barrel of the hinge.

Refinishing the Hinges

If you're not ready to replace the hinges on your door, you could do a few simple repairs. Make sure the screws that secure the hinge plate to both the door frame and frame are tight. If they're loose, tighten them with a power drill or screwdriver. Be careful not to tighten the screws so tight that they create gaps at the trim joints, or worse cause threads to be stripped.

If you're experiencing issues because the hinge plates are separated from the jamb and door hinge repair and jamb, you can Fix door hinge the hinges by applying wood glue to the plate's back and then inserting toothpicks or wooden dowels into the holes. The toothpicks or dowels will serve as a solid base for the screws and keep the plates from moving when you drive them into place. Let the glue dry before reattaching the hinge.

The screws may also be stripped or missing. This can be fixed by replacing the screws with longer ones. Use a drill that is exactly the same size as the screw hole to prevent drilling into the hinge or jamb.

After you've reattached your hinge, close the door hinge repair and check the gap between the door and the frame. It should be about the thickness of a nickel all around, or less if there's an existing gap that was caused by a previous door that was not properly hung. This should not be a problem if hinges are properly installed.

If you discover that the hinges are still loose, you can try adding an extra thicker shim between the hinge plate and the mounting surface, to create a little extra space. You can also take off the hinge pin and pound it down with a powerful hammer in order to tighten it up or choose an entirely new hinge. You can also lubricate your hinges using mineral oil or jojoba to reduce friction and keep them in position. Lubricating your hinges frequently can prevent them from becoming stiff and squeaky and also prolong their lifespan.

Cleaning the Hinges

The friction created by a hinge's constant movement attracts dust particles. Without periodic cleaning and lubrication, these particles get stuck in the moving parts of a window hinge repair for doors and then build up over time. As a result the hinge becomes stiff and creaky and its appearance may be damaged quickly. Regular cleaning, lubrication, and inspections will ensure the quality and function of hinges that are attached to doors.

Examine the hinges to determine how much rust has accumulated on their surfaces. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you are able to save the hinges, remove any loose rust by using wire brush and steel wool. Then, apply an industrial rust remover or a homemade solution such as lemon juice on the hinge. Allow the rust-removing solution to be on the hinges for a few minutes in order to penetrate and dissolve the remaining rust.

The tightening of screws can restore hinge functionality if you don't want to spend money or time on repairing hinges. If you've stripped the screws however, it could be necessary to attach a wooden dowel or shim to the hinge. Dowels made of wood are available in round rods of varying sizes and lengths. You can buy them on the internet, at woodworking supply shops and at home improvement stores.

You can also make an shim using metal or plastic depending on the type of hinge you have. To make a dowel, you need to cut an unfinished dowel into the desired length. You can then dip the dowel into a glue for carpenters and then insert it into the stripped hole and let the glue hold the dowel in place.

Before cleaning the hinges, put down a cloth or towel to protect your flooring from spills. After protecting the area, clean the hinges using a soft sponge or a cloth that has been dipped in a mild cleaner to remove dirt and grime. Also, tarnish and rust can be removed. You can use a toothbrush or small brush to reach difficult-to-reach places in crevices and tight areas.